HQM-1Chute blockage etection switch【技術參數說明】

HQM-1Chute blockage etection switch【運費說明】

HQM-1【規格書】

HQM-1【產品參數說明】

HQM-1【湖北杭榮】

Supply chute blockage etection switch LM-X, EXLM-X Explosion chute plug etector

HQM-1溜槽堵塞檢測裝置 LM-X溜槽堵塞檢測裝置的產品說明信息可能還不夠細致和，如果您需要更詳細了解LM-G溜槽堵塞檢測裝置 LM-X溜槽堵塞檢測裝置的相關信息或索取相關資料，歡迎隨時與我！

LM溜槽堵塞檢測裝置型號 溜槽防堵裝置廠家 溜槽防堵裝置 溜槽堵塞檢測裝置安裝與接線 LM-G溜槽堵塞檢測裝置 LM-X溜槽堵塞檢測裝置 溜槽堵塞檢測裝置開關

溜槽堵塞檢測裝置用途：

LM型溜槽堵塞檢測裝置，用于檢測帶式輸送機溜槽或漏斗物料暢通情況，當物料堆集過多造成堵塞時會給溜槽側壁一定壓力，使安裝在漏斗側面的檢測裝置的活動門開啟，使行程開關動作發出信號停機，避免惡性事故發生。

溜槽堵塞檢測裝置特點：

該檢測儀采用側壓活動門式動作結構，壓簧使壓門在故障后即可復位，背部開門，使接線、安裝及檢測極為方便，采用了密封的檢測開關，提 ，動作力為5公斤，極限行程為23，本機整體采用噴塑工藝，防止腐蝕；

溜槽堵塞檢測裝置主要技術指標：

觸頭數量:1常閉、1常開

觸頭容量:AC 380V 3A

動作行程:5~15mm

極限行程:20mm

環境溫度:-30~+40℃

相對濕度:≤90%(25℃時)

動作力:35~40N

:IP54

溜槽堵塞檢測裝置安裝:

1. 該機應成對安裝在溜槽相對的兩個側壁上,一般安裝在溜槽底部向上三分處,作為輕堵塞信號檢測。底部向上三分之二處作為重堵塞信號檢測。

2. 選擇好安裝位置后開一個260mm×260mm方口,然后在開口處上方約100~200mm處溜槽內壁焊接一塊300×80×850(mm)擋板,以防大塊物料落下直接撞擊活動門而發生誤動作。

3. 請將隨機配套的彈力橡膠板將開口*覆蓋,封閉,將彎角件焊接在溜槽內壁上,然后用M12×25螺釘溜槽堵塞檢測裝置與彎角件固定好。

接線:本裝置引出一條長1.5米左右的電纜線,按其芯線排號接線.1、2為常閉接點;1、3為常開接點。

溜槽堵塞檢測裝置工作原理及性能：

溜槽堵塞檢測裝置為門式結構，有壓簧復位功能。外殼用鐵板制造，經噴漆及防腐蝕處理為戶外型。整機結構合理，性能。

工作原理：當漏斗或溜槽物體堆集過多和物體過大不暢通造成溜槽堵塞時，堆積物料給漏斗側壁一定壓力，安裝在漏斗或溜槽上的活動門在壓力作用下活動門開啟，使行程開關動作，發出停機信號，排除故障后開關復位。

 LM-X, EXLM-X chute plug etector, blocking coal sensor, chute state etector, chute plug Sensor Prouct escription: LM-X-type chute plug etector switches for conveyor systems chute has occurre blocke, if blocke, the etector can etect the machine through the acss line failure signals, such as the fault signal is connecte to the use of electrical light or soun, ａn can emit light or soun signals. How it works: The material runs the chute clogge, the accumulation of material on the chute walls generate pressure, so that the activities of the etector signals the movement of the oor, when the clogging material remove, the oor automatically spring back into pla so that the activities. Main features: The etector uses sie pressure activity gantry movement structure, the pressure spring oor can be reset after the fault is cleare, the back oor, so that wiring, installation ａn testing is extremely convenient, with a high seale etection switch, improve anti- - protection level, the action for of 5 kg, the limit stroke of 23, the unit as a whole using spray technology, increase corrosion. Specifications ︰ conveyor bulk material hanling systems, chute plug is a more common phenomenon, it is often nessary after stopping by the fiel staff of the chute for reging pross, affecting the normal prouction ａn increase the lor intensity, resulting in unnessary economic losses. Z-□ Series rappers warehouse wall, can be use in material hanling systems, effectively exclue ue to the hygroscopic material, charge asorption, crystallization causes of congestion, sticky wall, oming ａn other faults, you can ensure safety in prouction, improve transport efficiency. The proucts are wiely use in metallurgy, electric power, mining, chemical ａn other inustries. Z-□ series rapping warehouse wall control box ａn chute etector with the use of reaily etect ａn prevent the occurren of failure chute blockage ａn improve the egree of automation. The evi has phase loss, over-current, short circuit protection, also has power inicator, limit owntime instructions, fault alarm functions. LM-X, chute plug etection evi chute plug etector switches for conveyor systems reprint link chute, hopper security protection for etecting clogging materials, conveyor system is essential for safety evis. One, chute plug etector works chute plug etector mounte on the sie wall of the chute when the chute blockage occurs, the accumulation of material activities must squeeze the oor, ａn to offset the start of the trip switch, an alarm or shutown signal . Troubleshooting, activities uner the action of the compression spring oor automatically reset. Secon, chute plug etector structural characteristics of the etector gate structure using lateral pressure activities, troubleshooting, spring thrust the active oor automatic reset; cast aluminum housing with a heavy coating micro switch contacts, high sensitivity, for Just 0.9kg trigger switch the machine can use importe limit switch, sensitive, ａn high reliility. Thir, the technical parameters chute plug etector operating angle 5 °, the limit angle of 10 °. Contact capacity: 1A/125 (C); 5A/250V or 380V (AC). Housing: ust, corrosion ａn rain. Protection class: . Contact Number: one normally open ａn one normally close (accoring to user nee to increase the number of switches) switch accoring to user nees acss to normally open or normally close form. Ambient temperature: -20 ~ 60 ℃.

Contact etail